Tilt
Inclinometer
Sensor that allows you to control the inclination of the cone when inserting into the terrain.
Fs
Lateral friction sleeve
The titanium sensor for lateral friction is highly sensitive and reliable.
The central unit produced in a special stainless steel alloy, guarantees extreme inalterability, which means even the toughest terrains can be tested.
Qc
Cone resistance
Cone of 10 cm2.
The sensor for measuring the resistance of the cone is available with maximum resistance of 50 MPa or 100 MPa.
u2
Measuring the interstitial pressure of the water
The u2 sensor allows you to carry out dissipation tests to measure the interstitial pressure of the water in the terrain.
It is possible to saturate the filter with silicone oil or grease.
Ring for tests with silicon grease
Filter for tests with oil
TGAS-12 is the acquisition for carrying out CPTu tests, dissipation tests, temperature and S-CPTu tests (which can only be carried out with seismic piezocone). The new program guides the operator at each stage and the five tabs simplify the passage between the different kinds of test, while the touch-screen capacitive monitor makes its use even more fluid and intuitive.
CPT-AS is the acquisition for carrying out CPTu tests, dissipation tests and temperature tests which are highly compact and robust. With just a few guided steps, it is possible to carry out different kinds of test. Lastly, thanks to its compactness and lightness, it is easy to transport in a practical case.
Configurations suited
to any situation
The P-Cone piezocone is functioning with: TGAS-12 and CPT-AS.
TGAS-12
CPT-AS
Technical sheet
Dimensions:
Length: 290 mm
Weight: 1.66 Kg
Diameter: 35.8 mm
Cone opening angle: 60°
Area of Cone base: 10 cm2
Sleeve lateral surface: 150 cm2
Technical specifications:
Qc sensor
Full scale: 50 - 100 MPa
Resolution: 24 bit
Accuracy: 0.005 MPa
Fs sensor
Full scale: 1600 kPa
Resolution: 24 bit
Accuracy: 0.04 kPa
u2
Full scale: 2500 kPa
Resolution: 24 bit
Accuracy: 0.04 kPa
Tilt
Full scale: 20°
Resolution: 12 bit
Accuracy: 0.5°
P-Cone15
The Pagani piezocone is also available in the 15 cm2 version.
From 5.678,50 €
Precision and high performance
P-Cone15 offers to the customer higher sensitivity in all tests carried out in soft and homogeneous soils characterized by extremely low values of tip resistance (Qc) and lateral friction (Fs). In fact, during the testing process carried out by Pagani Geotechnical Equipment it was found that the increased surface area of the cone allows a high sensitivity, and this gives to the operator the opportunity to get better accuracy in the data obtained in these extremely soft soils.
P-Cone15 also offers advantages in extremely cohesive soil tests. In fact, the cone tends to reduce friction, creating a wider borehole during the penetration phase which drastically reduces the lateral friction acting on the rods during, allowing the operator to test deeper.
The cone resistance measuring sensor is available with a maximum resistance of 100 MPa.
The P-Cone15 piezocone is functioning with: TGAS-12 and CPT-AS.
TGAS-12
CPT-AS
Technical sheet
Dimensions:
Length: 392 mm
Weight: 3.2 Kg
Diameter: 43.7 mm
Cone opening angle: 60°
Area of Cone base: 15 cm2
Sleeve lateral surface: 225 cm2
Technical specifications:
Qc sensor
Full scale: 100 MPa
Resolution: 24 bit
Accuracy: 0.005 MPa
Fs sensor
Full scale: 1600 kPa
Resolution: 24 bit
Accuracy: 0.04 kPa
u2
Full scale: 2500 kPa
Resolution: 24 bit
Accuracy: 0.04 kPa
Tilt
Full scale: 20°
Resolution: 12 bit
Accuracy: 0.5°